Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hello. I want to use nRF52810 as a connectvity platform connected to OpenWRT MIPS based board via UART. For some reason the only solution I can assure is to use 2 wire UART...
Dear Nordic support,
We are using SDK5 15.2.
Our application uses FDS to maintain configuration. One issue is that we have to change the configuration via phone app regularly...
Hi,
I am working on nRF52840 DK . C:\Nordic\SDK\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\peripheral\ uart I am sending data from Arduino and showing it on PuTTY...
Hi All:
I try to create a custom Characteristic,with nrf_ble_qwr,
but when set is_defered_write = 1;
connect with NRF_CONNECT APP, I can't write under than 20 byte,if...
Hi, we just saw that %BSKGEN was added in MFW 1.2.1. However, it is not clear to us what is the intended use of it. Could you please give us a bigger picture of it?
Is...
Hi there,
I have a rudimentary understanding of programming with the nRF chipsets and Segger.
In our project, we are trying to locate the position of a transmitter (nRF52833...
when design the product, BLE output power set at +4dBm, and test the real output power with Spectrum Analyzer. when test at the MCU direct output pin the output power is about...
Hello -
We are developing on the nRF52840-DK, using SDK 15.3.0 and FreeRTOS with tickless idle. The SoftDevice is disabled. Using the PPK v2.3.1 when our app is in System...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi,
I have a question regarding our approach to achieving high throughput UART transmission over BLE.
The protoboards we are currently testing have BL654 modules from...
Hi !
I tried to connect Thingy:91 to the nrfcloud using iBasis SIM in Germany. I want to try different telecom provider like Vodafone or Deutsche Telekom. Any recommendations...
So as part of my system I have something much like the Nordic UART service in that I need to send a notification when something arrives from the UART. Mine is a little bit...
For a Bluetooth Mesh device, or ' provisioned node ' , does provisioning happen more than once for a established network? Will this device ever need to be re-provisioned once...
Hi,
Is there is a sample for using the nrf-9610 I/O input for A2D to read a voltage across a resistor(using P and N for differential), given that I'm having Zephyr as ROS...
