Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Migrating SPI routine from SDK13 to SDK15. The following snippet worked in SDK13, but now I get an error "'nrf_drv_spi_t {aka const struct <anonymous>}' has no member named...
Hi there,
In our firmware we have a layer on top of FDS that handles higher level file system functionality. There is room for improvement in this layer that we created...
I am using nrf52832 with sdk 13.0.0.-alpha.I only want to boot the application and jump to blinky project address.For that i am using secure dfu example code.I am using IAR...
1. Are there any examples or recommendations how to realize ota dfu of ble central (device).
2. Can nrf52840 works like ble peripheral(UART service server) for smartphone...
Hi,
I would like to know how to program the code to connect the PC based on the ble_app_template.
The SDK version I used is V11 and the board I used is PCA2006, and I...
nrfjprog -f NRF52 --memrd 0x100000a4 --n 8
0x100000A4: ACAFE032 7AC54CAF
this is read by nrfjprog scipt as above and as below it is read by sd_ble_gap_addr_get.
0xCCAFACAFE032...
When creating a Server using nRF Connect version 2.6.0.
Cannot set the Descriptor 2901. It gives this error-> " Error occurred adding characteristic. (NRF_ERROR_INVALID_PARAM...
Details: SDK v15.2.0 using ble_app_pwr_profiling example. Windows 8.1. Tested uploading to nRF52 DK and Blunor BT832F.
Steps:
upload ble_app_pwr_profiling using SEGGER...
Hi,
I am using NRF 52840 DK ,rev.1.0.0(2018.36).For development using ubuntu 14 machine and segger IDE. Trying to use fatfs example with Transcend 4GB AND 8gb micro sd HC...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
I am using the development board based on NRF 52840 from Rigado BMD340. I connected the Eval Board via USB and in the NRFgo Studio it shows that the board is detected below...
No using bootloader.
the code cant run immediately is below when i enable the wtd.
After flashing the code by jlink,the code cant run till the wtd is timeout. i check...
We are using development kit for nRF52832 and trying to create the minimum current consumption that was stated in the datasheet which is 0.7uA while the system is off. However...
I did a search on Real-time debug, it's said for nRF52810, in Code generation, should set Debugging Level to Level 3, and Optimization Level to None Is that true for nRF52832...
