Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
Hello Nordic experts,
I am trying to add an output endpoint to the usbd_hid_generic example in nRF5_SDK_15.0.0_a53641a. I exactly followed the suggestions in
https://devzone...
Hi,
I am using nrf52840 preview DK as a transmitter and try to get rssi by a linux lib. and it works well. and now I want to find advertisement channel number, because the...
I try to integrate Mult-touch(touch screen) and Keyboard feature in a single program, when I run this program, the phone side(Android8.0 based) can only receive Mult-touch...
When using nRF connect for desktop on ubuntu I can't go through the "Select serial port" step because I got the following error message:
"Could not open the port. Please...
With the release of SDK 15 has come the new nrfx module API's which seem to be easy to port to. One thing I have seen in the nrfx templates is the use of the nrfx_config.h...
Hi,
We are using nrf52832 micro controller and our device is consuming about 14mA current right now.so i have 2 querries that
1. How can we put our nrf into low power...
Hello,
I encountered an interesting issue with SPI0 on the nrf52840 that I cannot explain. In short, my SPI bus would stop working shortly after communicating with my slave...
Dear Nordic Semi, I play with NRF24L01+ shield and, what I control using STM32F411RE or ADuCM4050. Once a while, NRF24L01+ chip stops and on the MISO line with permanent 0xFF...
Hello,
I have been working with the example ble_app_hids_mouse to learn a bit whitelist. My code now doesn´t have anything about the mouse anymore since i only care about...
Dear Sir / Madam,
My customer is asking me if nRF51822 is compiled to the requirements of China's RoHS 2.0. Below are the requirements for tour reference.
China RoHS 2...
Hi
Can you please provide an example/pseudo-code on how the channel_mask member in the ble_gap_adv_params_t struct is used? The only examples provided in the SDK and the...
I have open a brand new nRF52 Development Kit. It is not recognise by the nRFgo Studio. I have tried the trick you mention on this thread:
https://devzone.nordicsemi.com...
