after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have nRF8001 configured with Arduino M0 pro, and I am having problem regarding how to set static passkey. I came across the fact that softdevice API can store static passkey...
Hi, I just recently bought nrf52832 dk board. I am really new to this. I have prior experience on Arduino only. I started working on nrf52832 dk board with the help of nordic...
Dear Nordic Team,
We are using nRF52832 with a IQS231A for proximity detection for a new product, the pins are connected to SDA and SCL and everything is routed as in...
I am now using nrf52832 sdk14.2 development, as a slave device, I want to set the slave's Bluetooth interval is 1S, I set the following parameters: #define MIN_CONN_INTERVAL...
Hello,
I have nRF52832 with custom board and using SDK15 with Keil uVISION 5. I am working on beacon example and I have modified it to show battery level. I have done necessary...
I am using the bootloader_secure_serial example from the SDK 14.0.0 on a 523832 DK. I have erased the device and flashed the softdevice and bootlader on it. The LED1 is turned...
Hey, I would love some guidance on this:
1. I have one NRF52840 advertising constantly at 8dbm, this device is connected to power so it's hard coded to the maximum transfer...
Greetings,
Based on your librairies/examples, I can succesfully write and read data from an external flash (MX25R6435F) using QSPI with DMA.
I'm using a custom board with...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
Hello,
I'm using IAR 8.22.1, SDK 15.0.0, S132, nRF Connect V4.19.2.
I've loaded the 'secure_bootloader' example to PCA10040 EVB.
The device is recognized as DFUTARG...
Need to pass data from a battery powered sensor to a PC via a RF link. Would prefer
a COM Port emulation at 115,200 Baud. I already have a pair of nRF52 Development
Kits...
Hi guys,
Going through mesh packet format today and I'm stumbling upon the time_required_to_send_us method in broadcast.c which is used to calculate and indicate how long...
Hi,
I read and tried Mesh DFU given in " DFU quick start guide of nRF5 SDK for Mesh v2.0.1".
It says "To perform DFU transfers over mesh, use a customized version of...
