Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
All standard SDK examples disconnect immediately once I try to connect to from Android device. But when I flash the same sketch to nRF52-DK, I can connect successfully.
...
Hi All, on the right of nRF Connect v2.2.1,the "Start scan" button is invalid, I press "Alt+S", get a message "No adapter selected or adapter is missing state. Failing." I...
Hi,
I know that MtConnect05 is not a Nordic product but it contains a nRF52832
and these questions are about SDK for mesh usage.
The questions:
1. What does this...
I am a newbie for Nordic development boards. I recently bought a thingy 52. When I was searching for how to upload a custom firmware of my own (After disabling few BLE services...
Hi,
I need a button and a led for my project. I like the BSP library for all it's power saving features but it looks like it's not flexible. I want a custom event for the...
I am starting with Thingy and I am having some troubles.
Background is I have done some work with nRF52840 that sends beacons one-by-one with different payloads. And then...
Hello,
I have 2 issues, please help to let me know and clarify them...thankful for your support in advance....
I need to know the confirmation about the usage of fds...
I am using a custom board based on nRF52 (nRF52832-QFAB-R). I am using the ble_hid_mouse app and performing the initialization for SPI in the main routine. But with the SPI...
Hi
which is better for reduced current consumption
1. lesser value of of MIN_CONN_INTERVAL, MAX_CONN_INTERVAL with large SLAVE_LATENCY
2. or vice versa
Thanks...
I tried using the serial code in peripheral/examples to transmit At commands to the esp module but did no get any reply.Is there any reference example which I can use to connect...
Hello All,
We are working on automotive application can i use 3xspi in nrf51824. i.e is it possible to configaure 3 masters in nRF51824 ?
thanks in advance
pavan
I have the nRF52-DK arduino board with a nRF52832 chip on board, is there any examples where I can read the Analog inputs on the arduino board and send them over bluetooth...
I'm downloaded a copy of the "offline" documentation, but its just a html file, is there a copy in PDF or any other searchable format?
It would be nice to be able to search...
Hi. The same issue I have is described here, but I've been asked to post a new question:
https://devzone.nordicsemi.com/f/nordic-q-a/29084/why-sd_ble_gatts_exchange_mtu_reply...
