Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I need to count millis from nrf52 start
I have seen that all are using rtc1 but I did not find any example from which i can integrate it to my project.
We are in the development stage of a product that uses the nRF52832 and have acquired a nRF6707 Rev 1.1.0 power profiler kit to make power consumption measurements.
I am...
Hi,
I'm trying to download Invensense's "Embedded MotionDriver 6.12" in order to compile the Thingy:52 SDK, as suggested here .
It seems that this wasn't previously...
Hi everyone,
I am currently trying to implement USB headset on nrf52840. As far as I can see the audio example from SDK14 uses SyncType=None meaning that bmAttributes bits...
I want to change type from "uint32_t val1 = 0xAA01" to "uint8_t val2 = {"AA01"}.
Then, attr_char_value.p_value = val2;
=> sd_ble_gatts_characteristic_add(p_rms->service_handle...
I am currently trying to develop Mesh applications using the Nordic Mesh SDK and the nRF52840 Dev kit. The problem that I am having is that my testing equipment isn't able...
We have a custom hardware device that uses the nRF51 and the S130 softdevices. We are able to connect our device to our app on iOS and Android and through a web-bluetooth...
I want to erase selected pages from the NRFflash memory (Not whole flash).
I have defined one function for NRF memory erase. In that, I have followed following sequence...
Hello, i am using NRF 52832 QFAA
In pstorage_platform.h I see
#define PSTORAGE_FLASH_PAGE_SIZE pstorage_flash_page_size()
and the return value of pstorage_flash_page_size...
Hi Nordic,
I have been quiet for a long time but here is another question.
For the project I am working on I want to measure the current with the PPK. Although it seems...
Hello. When I received nRF52DK, I have successfully uploaded some examples also with softdevice through the Keil IDE. But after few days Keil and also Segger IDE stopped detect...
Hi. I'm new to both the nRF24L01+ and to this forum.
I'm intrigued by the prospect of using these amazing little transceivers as RF modems. Because I find elements of the...
Hi,
On SDK12.2, I replaced main.c in ble_app_template with one in twi_scanner and modified sdk_config.h.
But, no expected log, even "TWI scanner.", issued to terminal...
Hi,
I want to add a service to the "ble_app_beacon example" that i can change
the value of the major and minor directly via nrf connect, some one can help me
to add the...
