after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I did some power measurement on the nrf52 DK with the Nordic profiler kit and the result was way more than what we could expect from a nrf52 (about 1 mA). Even in...
I am working on the ANT connectivity for a product we've developed, called RunScribe [a shoe-worn running sensor], and am seeing some issues on Fenix 5 watches with our ANT...
Hi,
I'm trying to implement run the ESB and the BLE concurently using the timeslot API.
I started from this example : devzone.nordicsemi.com/.../
The problem is this example...
Hi,
I'm quite a beginner to this whole nrf52832 world and I'm trying to read some data from a flex sensor wired in series with another resistor connected to VCC now I understand...
In brief our problem with rfx2411n is that rfx begins to draw 200ma current without any reason. Rfx is powered down, powered from 3,0v. And suddenly something happens and...
I have a device that runs with nRF51 chip with the NRF UART Service (NUS).
I have a Raspberry Pi 3 and I want them to communicate.
The device requires an authentication...
My question is related to peripheral device only. I have implemented an auto connection interval negotiation algorithm which works as expected and negotiates connection interval...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
I'm having trouble adjusting ram start setting using the new SES projects from latest SDK14.1.0
I have tried the project linker section placement macros settings of
...
