Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am trouble with private key generation in nrfutil. I am following the tutorial infocenter.nordicsemi.com/index.jsp.
When I am giving the command nrfutil keys generate...
Hi, do you have a central peripheral combo example which illustrates indication (not notification)?
Alternatively, if you could list the steps to change from notification...
It seems GPIOTE interrupt do not trigger when multiple IN signals are defined as GPIOTE_CONFIG_IN_SENSE_XXX(false).
It works when GPIOTE_CONFIG_IN_SENSE_XXX(true)
I am...
With SDK 14:
If I flash in this order:
softdevice_s132.hex
bootloader_secure_ble_debug_ with bonds_s132.hex
3. ble_app_buttonless_dfu with _bonds_s132_with_setting_page...
I am having issues to use 2nd UART. When I run Keil in debug mode it shows me three UART registers.
i) UART0
ii) UARTE0
iii) UARTE1
Is this UART0 and UARTE0 same thing...
I am using NRF51822 Rev3 and softdevice 7 in my project. On communication with
Android device sometimes the link disconnects with disconnection reason61(0x3D)
BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE...
I have used nrf24l01+(production year=2015) in my project and my board and my program are working well......but when I change nrf24l01+(production year=2016) my board doesn...
I have an application where knowledge of the current date/time is important. This is implemented by the central passing the time to the peripheral when it initially connects...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
Hi everyone,
I am currently working on a project that leads me to save a respectful amount of data.
Some of the objects that I save size a few KB actually.
I would...
Estimate battery life for FOB CR 2032 -240 mAh
We are developing remote with CR2032 battery and using Nordic nrf51-1822 BLE, 960 m sec connection interval, RX 1 packet...
I want to use nRF52840 Device to implement non-connectable advertisement and scan on one board.
To be more specific, I want to advertise information for some time period...
I am using NRF52 SDK14.0 and SoftDevice S132 v5.0.0. Application freezes somewhere in SoftDevice if sd_softdevice_enable() is called after nrf_drv_clock_lfclk_request() was...
Hello All,
Where would I find a library file for a PID controller? Forgive me if there is an obvious answer. I'm new to working with Keil.
Thanks for taking the time...
