Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am using
nrfgo studio ver 1.20.0.2
s132_nrf52_1.0.0-3.alpha_softdevice.hex
nrf52832_xx_aa_s132.hex supplied by Nordic (ble_app_template)
emIDE 2.20
The firmware runs...
Hi,
with the pstorage library, is it possible to store data at a specific flash address?
The background of the question is that I would like to store data in flash, and...
Hi,
I am using PWM for a buzzer. It is working, but the current consumption is always 300uA when PWM is not in use. This minimal current consumption appears right after...
1: my nrf51 SDK board not work , I replace the USB control IC--ATSAM3U1C-AU(the old is ATSAM3U2CA-AU),can you send me the firmwair of JLINK with this IC and the contacted...
Hi Nordic,
I want to know, how the button_push_sequence works on case of handling different events at different button_push sequence like... (--nrf51-ble-app-lbs--)
...
I'm using the pre-compiled nRF51-BLE-Driver-Win driver (v0.5.0) on win7 64b with python2.7 and an nrf51 dev kit dongle running the precompiled 115.2k s130 connectivity firmware...
BLE.c
when no connection creat between android nrfUart app and backon kit so autometically sleep in 180 seconds,
but i have need sleep condition in connected mode of...
This isn't a question, just a tip/head ups for people. Spent more than a few hours wondering why all my Flash settings all of a sudden were no longer saving. I found that...
Hi, the title says it all really. I'd love to get my hands on a sample application from the Nordic github repo (or elsewhere) which shows clearly how to implement for S110...
I've read the document, 51822 Product Specification 3.1
But I can't find which pins are assigned for SPIS.
I'm using QFN type.
Directly speaking, can I achieve SPIS...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
in our final device, I want to give the user the opportunity, to close an opened BLE connection between our device and another smart device. This should be done...
I have 2 boards. The first board, I run the demo project code for ESB PTX. And it works fine. However, I load the same code on a second board, and "nrf_esb_enable()" never...
I intend to use ESB to transmit data every a few hours. Since I want to use a beacon board, I assume the ESB app needs to sit on the S110 softdevice.
I added S110 to the...
