Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
I take the nRF UART 2.0 for reference. I make the nrf51822 be always sending packages ,and if it sends one package succussfully,and the smartphone just shows what it receives...
Hi guys,
Is there any way that I can re program the MAC ID of the nRF51822 devices through the SWD interface? I was able to do this using the UART interface with the BL600...
Got a Keil ULINKpro D debug unit with my Keil uVision\ toolchain license. However that doesn't seem to work with the Nordic nRF51822 on my Fujitsu module Development kit....
Hi,
I referred to the sample code "led_radio_example" and I think I might miss some thing so the program does not work.
The sample code indicates to use a terminal program...
Hi,
I am trying to understand the behavior of auto acknowledgement with payload for an application I am working on, I am hoping for some clarification on how ACK with payload...
I seem to be getting into sleep() fine with not able to connect to my app!
but getting back to work from sleep() is taking toll and its not working simply.
I'm trying...
Nordic will release a new development kit in april, named mkit.
It is based on arm mbed .
Writing a ble app will be easy, fast and simple using mbed BLE API .
My question...
Hello,
I compiled the pc10001/blinky_example with gcc/makefile, i can flash it with nRFgo Studio and it works. But if I try to compile/flash the pc10001/button_radio_example...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
