I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I have an issue when I want to read an attribute from a toll to my nrf52840 device.
For exemple attribut 0 of cluster basic, if I forge a general read request for...
Hi,
I am in the process of porting an application from an nrf52 to an nrf51 due to availability issues. One problem I run into is that bluetooth events are handled in...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
I have checked out and built the iBeacon sample in zephyr (samples/bluetooth/ibeacon) for nrfconnect version 1.7.1. I tried building for both the nrf52840dongle and nrf52dk_nrf52832...
Hi,
I have a custom 9160/mfw1.3.1 board with a set of matching networks and I need to setup MAGPIO to control these. This will only be used for cellular, not for GPS.
...
Hello,
We have produced a product that uses the 82520 chip. This product uses the NUS service. We want the Windows PC to use its built-in Bluetooth to connect...
Hello,
I need a PMIC for a lithium polymer rechargeable battery solution.
The nPM1100 from Nordic is interesting, but I see there is a cap on the output current available...
I cannot get the blinky example to work with my NRF52 development kit. I used the example in the pca10040/blank/ses folder and it worked fine. I then modified the code per...
