Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
When I'm tuning the RF output (front end) of the nRF52832 to match 50 Ohm what state should the chip be in? Unprogrammed with power on or off? Or in receive mode with power...
Should a firmware written for nRF 52832 run smoothly on a nRF52833 if no changes in functionality are desired?
If changes to the firmware are needed, which layers must be...
Hello , Vivek here. I am planning to use NRF52832 in my design and interface it with a microcontroller. And i am new to handling bluetooth protocol. When I was going through...
Hi,
i am using nRF52840 SoC and Had confusion on pin mapping for SPI (external flash) and I2C (external sensors) as below:
I found one similar query and it was said...
Hi,
I would like to write a code where I send a packet from a nRF5340 DK to another nRF5340 DK by using Zigbee.
I would like to also be able to use printk and see the...
Hello Development team!
First off, many thanks for all the help provided so far.
I'm trying to add the ZCL messaging cluster to the multi sensor example, how could I go...
SDK: 15.3.0 Example: ble_app_multirole_lesc DeviceA: EYSHJNZWZ (nRF52832)
I want to know the relationship between API and events. Take "sd_ble_gattc_characteristics_discover...
Hi nRF Support,
I get nRF5 SDK version 17.0.2 and learn Peer Manager handler implementation (pm_handler_flash_clean function). Lets consider this case:
- 2 bonded peers...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available.
I did:
update the modem with mfwnrf9160123...
Hello, I am trying to program the peripheral uart sample on to my Thingy 91 using the nRF9160dk and 10 pin connector. I am able to successfully build and download the target...
I hope I am posting this in the right place but I am looking into learning more about developing devices that use Bluetooth. I have been looking into getting a dev board but...
Hello All,
I am working on nRF52840 DV-kit, using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71
I am trying to create .c and .h file in my project for gpio_configuration...
Hi,
I have layout a borad with nRF52810 and use IO to control other ICs.IOs map as blow.
#define LSM_6DS_SPI_CLK_PIN 9 /**< SPI */ #define LSM_6DS_SPI_CS_PIN 4 #define...
We are using nRF52840 chip for our development and till now we have used nRF SDK's zigbee CLI example for development.
Now we are interested in nRF5340 chip but I have not...
hi，
iI'm newer useing nRF5340， nRF5340 two cores communicate via IPC ,then exchange data through which path that is IPC or CTM ，What's the difference between IPC and CTM...
