I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I am using the radio test example code where in the interface is through cli. Our custom board has a serial port in UARTE1 instance
how do I configure the cli to...
Hi everyone,
I am trying to develop an application and I need to solve this situation : when the modem is not able to connect to LTE-M network, I still want to be able...
Hi,
I already replied to an old discussion without response so far:
https://devzone.nordicsemi.com/f/nordic-q-a/57449/nrf9160-mipi-rffe-support-for-more-than-one-device...
Hello,
I am using ADuCM350 microcontroller with a build in Bluetooth NRF8001 on board for a school project. I want to program the bluetooth connectivity over SPI0. I will...
Hello Everyone ,
With variety of motion sensors on Thingy:52 , can it be used to detect if a person has fallen ? If 'yes' then how accurate the results will be ?
If...
It's a coding question. Maybe it has nothing to do with NRF.
I'm playing the central example hrs. I have a custom .c file that wants to access the m_hrs_c variable defined...
Hi,
We are developing a system with nRF52840 chip and we have to feed the soft device (s140) hex file & our application hex file into custom board which we are developing...
hi,
For NRF52840, is the 125kbps sensitivity the same as on Radio? I used the 125kbps long distance mode, but the distance was not up to the ideal state, the deviation was...
Good morning,
I'm developing an application for nRF52805.
I saw that in SDKFolder/config there are all "complete" sdk_config.h files for all nrf52 targets except for the...
Hi,
I am using own hardware board based on https://www.raytac.com/product/ins.php?index_id=24 module, it uses nRF52840.
I
I am facing an strange issue that UART is not...
Hi,
can anyone provide any insight into moving beyond a pca10040 development board and creating a project for a custom board? What are the steps that you have to go through...
Hi,
We are looking to be able to reflash our devices on the field, as well as do FOTA. Critical device information (serial number, encryption keys, etc) are stored in the...
How does the ADC gain block work.
Suppose using Vdd=3.3V as ADC reference, analog signal input from 0 to 3V and gain 1/4
What will be the ADC core voltage for single...
I have an application where i have to regularly send gps data to an mqtt broker. I started with the mqtt sample which works fine, and i also tried the gps example with assited...
