I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi, I am trying to do unit testing of my application, but at the moment I am not able even to compile and run a test of the example. I am using ncs v1.1.0 following this example...
I downloaded the following repo from github: https://github.com/NordicPlayground/ncs-display-ble-example , applyed the patch and i uploaded the scketch to my nRF5340DK , but...
Good Afternoon, I recently got an nRF5340 PDK kit and would like to get OpenThread examples for this board.
If possible I would like to demo the OpenThread CLI example....
I'm using this code to handle interrupt and power down the device. However, this code is not working the softdevice.
I just want to power on and power off using an interrupt...
Hello,
I am working with the nrf_cli_ble_uart (SDK16), I am able to connect, exchange data, however when I disconnect I got an assert :
It is indeed in ble_nus.c ...
Hi Nordic Team,
I am using a simple GPIO (tx/rx controlled via GPIO) FEM (PA/LNA) with connected to nRF52840.
I know I am allowed to crank up the TX power of nRF to +2dBm...
Is there support in NCS for MCUboot images encrypted with a different encryption key (not the same key as the signing key)? How is that configured (via prj.conf, etc)?
Hi, I have a nRF5340 based target board running SMP server plus MCUmgr. My ultimate goal is to reproduce on Windows the DFU over serial I already do from Linux. Tese are the...
Im trying to interface ADXL345 with nrf52DK via I2C. Im using the reference drivers in below link
https://devzone.nordicsemi.com/f/nordic-q-a/40822/adxl345-and-nrf52832...
Hello,
I am trying to connect a BLE HRM strap with nrf52382 using example/ble_central/ble_app_hrs_c/pca10040/s132
I am getting this on debug
<info> app_timer: RTC...
Hi,
I am having issues programming my custom nRF5340 board and was hoping to get some advice on the issue.
When programming using nRF Connect for Desktop (Windows 10,...
Device nrf52832 Custom board and nrf52DK with nrf52832
SDK 17.0.0
IDE Segger
when SPI interface is initialized by nrf_drv_spi_init, then MISO line behaves as follows...
Hi! Recently I have been working with Nordic products, starting with NRF52DK. I want to pair/bond cycling equipment (BLE and ANT+) with NRF52DK. After no success with ANT...
I am using pc-ble-driver-py to create a custom scanning and connecting application, but I'm running into an issue regarding the UUIDs of a particular service after connecting...
