I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi
According to the product specification, the power fail comparator nRF52832 has a threshold tolerance of at most +/-5%. When I configure the power level warning to 1.7V...
While trying to investigate my Softdevice assert issue a bit more in depth, I noticed a bug in timeslot_timer.c :
The function timer_mut_lock() sets the variable m_timer_mut...
I have a sensor that uses 3 different BLE mechanisms. It is part of a mesh, it sometimes sends beacons and it provides GATT services in a peripheral role. The project I'm...
Hello,
Are there plans from Nordic to provide locator engine to customers? Other competitors offer this benefit, which reduces development time on the client side to create...
Hello All,
We are using NRF52840 module, need to work on serial bootloader.
I have gone through the bootloader example, our requirement is need the serial(UART) bootloader...
Hello,
How the modem selects it band of operation. Is it done automatically selected by the modem after registering to the base station? or is it assigned by the base station...
The modem firmware version 1.1.4 has been certified by Verizon, and the corresponding NCS version is v1.4.2. Now Nordic has released the NCS SDK version v1.5.0. This version...
To the kind attention of Nordic support team,
if it is not much trouble I would like to know what you consider a good/acceptable ble antenna efficiency in
desktop environment...
Hi,
I am using an nRF52832 with S132 and SDK v15.0.0 and already read in the forum about issues related to the SAADC calibration (inlcuing the erratum [86]). The problem...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
