I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
HI Nordic
I currently have a 2 separate projects, that i'm trying to merge.
- Production test tool with RTT CLI interface on nRF52840 (Here I use JLink.exe -device NRF52840_XXAA...
Hi Nordic teams,
I'm developing the function of Mesh DFU. I've test the nrfutil tool locate on https://github.com/NordicSemiconductor/pc-nrfutil/tree/mesh_dfu , and it works...
Hi All,
I have designed one device using nRF52840 MCU and software SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
From Software end all features are implement and...
Hi Sir,
As check nwp_024_v1.6.pdf, it only shows the tape real information w/ below series.
nRF24
nRF51
nRF52
nRF8000
nRF9160
I don't find the information for...
Hi,
I have a SPI peripheral connected to the nRF960 DK. In order to access this correctly, I need to be able to write a byte to a specific address first and then read back...
Hi
The NRF52832 I used seems to have accidentally turned on the read-write protection，Cannot establish a connection using JLINK now，Is there any way to turn off this read...
Hi, We are developing a robotic product using nRF52840. I would like to know if Nordic officially supports Zephyr OS and have plans for supporting features in long term?
We used sd_ble_tx_buffer_count_get() to get maximum tx message can be sent in nrf51. However, this api is removed from nrf52840.
Is it equal to the setting of NRF_SDH_BLE_GAP_EVENT_LENGTH...
I am using NRF52840 and SDK1600. Currently, my program uses 50kB RAM memory according to Segger Embedded Studio. NRF52840 has 250kB RAM memory, so there is plenty of space...
Hi,
We are building a prototype based on the asset tracker demo application. We had interfaced different sensors on different peripherals (2 on SPI and 2 on I2C). However...
I have applied the errata 171 workaround to a zephyr code base with an MX25 chip and set the speed to 96MHz - when I run the application (engineering D silicon) with a scope...
Hi
I have used ble_beacon example to configure DK board as beacon here i wanted to pass custom data inside the code and print those array code on output debug console to...
I have an embedded Linux platform which uses an nRF9160 connected via UART. The nRF9160 has been loaded with the serial LTE modem firmware, version 1.3.1.
I've been experimenting...
Hi!
I'm developing the NRF9160 target from a raspberry Pi. The problem is that I need occasionally to perform modem firmware upgrade, and I can't figure out how to do it...
