I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
This is a arduino code, but got to do it in nrf52840dk can you tell me what should i change , i have given code link and library https://github.com/AurekSkyclimber/DIY-Haptic...
Hello,
I am using NCS v1.3.0 examples and also my custom made C++ code with Visual Studio Code V1.48.2 (Since the latest version of VS Code V1.5 is having official issues...
it seems that Figure 2 on this page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fpwm.html is incorrect, or at a minimum the figure does not do what the...
Dear Nordic Experts, although the title says it all, please allow me to briefly explain the situation: I'm working on a ble mesh firmware and an accompanying Android app....
Hi,
I have been trying to run nrf9160: AWS_IoT sample on Thingy91 but have been getting the following output in the serial terminal:
I couldn't figure out what mqtt_connect...
The Situation: I am having a Sensor Node that is based on the nRF52832 (S132) and does two things: advertise some sensor data and store sensor data to the internal flash....
I'm porting an application that communicates BLE with a smartphone via nRF52 from SDK15 to SDK17.
It will be Connected, but I can only receive 2 bytes.
Also, even though...
NCS 1.3.0 mbedTLS configuration to the existing app in SES results in compilation error.
The SES project file contains the define like so -DMBEDTLS_CONFIG_FILE=\\"nrf...
I recently came across the Smart Remote 3 product by Nordic. I currently have a product in development that is a remote that has very similar functionality. Even down to the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
