Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I have a setup where nRF91 and nRF52 on nRF9160 DK have to exchange ASCII strings over UART. nRF91 runs Zephyr and nRF52 - nRF SDK for Mesh.
When nRF52 is unprovisioned...
We are using mesh SDK v3.2.0, nRF SDK 15.3, nRF52840 DK and SES as our IDE.
We had a mesh network with around 5 devices and after a while 2 of them just stopped sending...
Hi,
We are developing the product based on nRF52840 Chipset for BLE Application. We are using the Segger Embedded Studio ( SEGGER Embedded Studio for ARM Release 3.52a)...
I implemented some NonSecure Entry functions in my app and I've noticed that if I check an object using the cmse_check_address_range intrinsic that the check fails if the...
Hi,
I have Six services in my project to be advertised and make available to the user at a time.
first I have faced problem while advertising two vendor UUID's.I solved...
Hi! I'm planning out the connection of a micro-SD card through SPI to the nrf52840. I'm reading through the documentation and when powering the nrf using a Li-Po through VDDH...
I am trying to add a bootloader to my application which I have currently running on an nrf51822 with SDK12.3.
The first problem was that the examples from SDK12.3 do not...
Sir,
I finally got success to measure the Coin Battery using a analog INPUT of NRF52832, AIN4
i am using ZEPHYR RTOS
I have to connect the BATTERY VDD to the AIN4. ...
Looking for Android logging utility where host processor on a Mobile device is interacting with nRF52810 over UART interface.
or Provide a stand alone logging utility that...
where can i search whta the mean about <type>,<result>,<datatype>,,<qos>,<retain>.....Etc.
EX: #XMQTTEVT: 4,0
I Don't know what these values represent
thanks
...
Hi,
We're using a 51422 with s130 to perform OTA DFU.
Both bases for bootloader and central are from sdk 12.2.
We have already implemented the older DFU (non-secure...
Hi,
I want to use the Code Profiling feature from Ozone with my nRF 52840 DK and the j-Trace Pro Cortex. Compiling and debugging my program works flawless inside Segger...
I am trying to figure out how to use the TX part of the BLE NUS Service to send a notification. Currently I am receiving data via the nus_data_handler, however because i will...
