Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
Hello ,every one ,I found that the nrf Connect will disconnect it self after connecting to the device after 30 seconds, I'm using the sdk15.3.0 ble_app_template example,I...
NRF5_SDK_15.2.0
I am run my android code on android 9 and android 7. Unfortunately my android 9 is paired sometimes and not paired sometimes. especial after i tried to connect...
I am currently developing applications using nRFtoolbox. In case of ses, we are developing a template, but the application does not produce a negative value. In this case...
Hi, this is my first time using nRF52832 as a central device. (S132 6.0.0)
I set up the scan timeout parameters, it does stop scanning at the time I expect,
but strangely...
Hi,
It seems I'm running into the fairly common "solution load command failed (1)" error on a nRF42840DK board.
The console output in Segger gives me the following:
...
Hi, I am using mesh sdk 3.20 and nrf52840.
I am using 3 nodes for testing. One generic on off client and two generic on off servers.
I believe that I have managed to get...
