Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
I need to compute the checksum for a firmware image and I'm looking for suggestions on what works best.
I'm using SES and I don't see any checksum or CRC of the firmware...
In Beacon Why UUID is required ? Where exactly it will be useful ? I understand Major value Minor values , company identifiers values . it will difference the beacon location...
Hi guys,
i'm trying to deploy a BLE iBeacon on an Holyiot-17120 board. My code runs fine on the nRF52840 USB Dongle DK, but on this board works only when I've debugger...
Hi All,
I want to configure 64 MHz internal oscillator (HFINT) on my nRF9160 DK to reduce the wakeup time of nRF9160 chip from system-off mode. Is there any example available...
Hello,
I'm looking to be able to adjust PWM output frequency around 100KHz in 100Hz (or close to it) steps. I understand that no matter which method you use the implement...
Dear all,
I'd like to customize bootloader, I need more space so i modified flash address from example: FLASH ADDR (0x78000), SIZE (0x6000) to FLASH ADDR (0x69000), SIZE...
I am using the code above and already try it in the compiler . It should work but when I try to display in termite it only display .000 for microseconds.
Example
1987...
I used thingy s132 pca20020 sdk and i changed the code.
send data.accel.x, data.accel.y, data.accel.z data when data over the limit in swith case DRV_MOTION_EVT_RAW in drv_motion_evt_handler...
Hello all!
I've been researching DFU over BLE, between a central and a peripheral.
The peripheral is possible to upgrade over the DFU Bootloader. I've tried upgrading...
Hi,
I try to use cmake in Linux to get the hex file fo bootloader. The Platform is nrf52832_xxAA, the toolchain is gccarmemb. I read the given cmakelists but many variables...
Hello!
I am in the final phase of development and currently focused on reducing power consumption of my device.
To improve power consumption I'd disable UART if not...
Hi,
I am using nrf52 DK board.
After uploading my bootloader and application on a device that is connected through bluetooth with my board, i want to know the application...
Hi,
i'm facing a problem with a connection.what i understand from ble there are 2 mode in ble such as advertising mode and connection mode. i'm working on a project, which...
I have designed a custom board using NRF9160, but it has some trouble such as can't connect to LTE/NB-Iot, detect GPS signal,... So I want to use development kit to set up...
Hello,
SDK: 15.3.0
nRF52840-DK
IDE: SES
Example: flash_fds_s140_pca10056
Example Location: nRF-SDK\examples\peripheral\flash_fds\pca10056\s140\ses
Example Documentation...
