Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
the nRF5 SDK v13.0.0-1.alpha uses the BLE_GAP_PHY_CODED constant to indicate a coded PHY.
The BLE 5.0 standard specifies two options for coding: S=2 (500 kbit/s...
My app (SDK12.3.0 + S130 v2.0.1) is being prevented from advertising because flash_access_in_progress() is true (m_queue.count != 0) on ble_advertising_start (ble_advertising...
Hi! I'm trying to add the nRF drv_timer library to the ble_app_template example project (BLE Peripheral).
I have added the nrf_drv_timer.c file to the project, and the directory...
I need to switch between 3 central devices (device slots, rather) with a peer manager and SDK 12.3.0 (nrf51822-based keyboard, see sdk12_3 branch for a peer manager https...
Hi,
I have a problem, like this fellow engineer here , but the solution is not applying for me.
Our firmware support different modes of operations. Mode changes are...
Hi,
I was testing out the nrf52840, and i wanted to initialize the BNO_080 sensor with the nrf52840 DK. Now, i realized that if i want to read from registers to get the...
Hi, I'm using nRF52840-DK , SDK 15.0, buttonless DFU sample + secure bootloader I see that resuming DFU works only after disconnect, but no longer on sw reset or power down...
Hello
I have seen in the various examples that most of the time the output are digital (0 or 1) . i program a PWM signal to make any DC output on the pin 18
but unfortunately...
I am developing a windows deskop application for BLE devices.
which laungage is the prefered for this type of Desktop application having predefined libraries..
Nordic...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
I have seen nordic contains QDID 111537 for mesh profile subsystems. Is this profile subsystem includes the Mesh Model or nordic have a plan to get Mesh Model QDID seperately...