Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello. i testing zigbee coordinaator example with zigbeee device. Device was joined to Zigbee coord/ network.
Couldn't i get device payload data in coordinator source code...
I have the UART configured using the standard boiler plate code, with flow control enabled, where the RTS output is assigned pin 5.
I have defined a GPIOTE pin 25 as an...
We are working on a solution that involves a central provisioner that provisions a MESH network of sensors that it subscribes to. We need to be able to replace this central...
Hi,
I am currently drawing up a schemtic involving the NRF52832 on Proteus 8.
I have been trying to find symbol, footprint, and 3D models of the NRF52832 online, however...
Hi!
We are using a custom bootloader for our device. Current version of this erases everything from 0x0 to bootloader start address, and then writes MBR + Softdevice ...
Hi,
I have a question about ADC reading in ble_app_uart__saadc_timer_driven__scan_mode in SDK 14.
Let's say I'm using a double buffer, and I have 3 ADC channels (so...
Hi,
In my project, I am use nRF52832 for controlling ws2812b led strip with 8 leds.
I am use SDK 14.2 and s132_softdevice_5.0.0.
I have problems with the latency of...
I have a custom board of nRF52832-QFAB-B0 on which my application works well with SDK15.0.0 & SD132 v6.0.0
To perform DFU,
1. I copied the relevant parts of ble_app_buttonless_dfu...
There is always one kid in the class who wants to correct the professor and make himself look special.
That is me.
So: In file nrf_sdh_ble.h, line 76
@details This macro...
I am porting my own RTOS (named PicOS) to nRF52. So far, PicOS can run well without activating SoftDevice. I mean the SoftDevice is programmed on the flash memory but not...
Hello All,
I was doing some development on the Nordic nrf51822 and it was working fine without any issues.
I tried to remove some functions from the main loop (not removing...
Wich is the proper way to bring bootloader into deep sleep?
I'm using a modified version of the BLE Secure DFU Bootloader (SDK 14.1.0) for the nrf52810. I have added button...
We are working on non connectable beacons without any external I/O. They simply have a power and ground. Is it possible to perform OTA updates on such devices. Is there any...
Hello,
I am trying to use the extended advertising mode available on the V15 of the SDK (with SD S140 V6.0.0). I use the template example where i am currently advertising...
Hi,
I have developed part of my code using UART, starting from the UART example in \examples\peripheral\uart , but before continuing I need to start doing things over USB...
