I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
hi,In the host,
if(nrf_gzll_get_tx_fifo_packet_count(pipe) == 0 )
{
nrf_gzll_add_packet_to_tx_fifo(...);
}
In the devcice, every 5 min send packets to host ,but ack...
Hi,
I'd like to design a custom software an win10
to help in design a custom hardware using nrf51822...
at this time I have an eval board (PCA10028) whit a custom firmware...
We are trying to dump DFU code using Keil into nrf51822 IC. We are getting error, we are using SDK12. we tried many solutions provided in devzone, we were not able to solve...
Hello everyone,
I am trying to congifure two gpio pin (pin 6and 7) in standard high drive mode 5MA because am trying to connect those pin to the speaker inorder to increase...
When I program the board the COMP and Timers work fine. Upon removing the debugger and resetting the board it also works fine. But if I subsequently power off the board and...
Hello.
I don't know difference of GPIO's input/output direction setting.
There is two register for gpio setting.
DIRSET : Dir set register
PIN_CNF[n] : Configuration...
Hi there,
Is it possible to call SOC library functions before calling sd_softdevice_enable()?
In particular, i want to set up my interrupts with sd_nvic_SetPriority...
We want to use 52832 to control 6 LEDs. it is easy to use 6 IO pins to make them on and off. but we need these LED to blink. so we want to use one PWM module to generate 1...
When using the nrf_drv for spi master there are no problems when compiling. If I switch the SPI configurations to operate as a spi slave the compiler spits out "non-trivial...
Hi All,
I have just started working on interfacing SD card with nrf52 using SDK 12.0. I have to write to SD card at a rate of 84 packets per second and each packet consists...
Hi
I am checking out NRF51822, NRF24LU and NRF24LE1.
Below are my design requirements:
Smaller the size, the better. 7x7mm is OK. prefer smaller.
Lower power...
Hi, Nordic
I have 3 nRF52 devicies, one as Gzll Host, two as Gzll Device.
they use Gzp to pair, when paired, two Gzll Device send payload via different pipe ( 2, 3)...
Hey everyone, I'm trying to use lmt70 with nrf51822. So, first of all, nrf51 has 10-bits ADC, the data sheet of lmt70 is recommended 12-bits of ADC.
I plugged the sensor...
I use nRF51822 (Multiprotocol Bluetooth low energy/2.4 GHz RF System on Chip).To transmit informations with smartphone.
I have to set up a self-certification application...
Dear Nordic.
Is NRF_POWER->GPREGRET register writing in NVMC?
FICR and UICR is saved in flash memory(NVMC) as written by [nRF51_RM_v3.0.pdf].
But, GPREGRET register...
