Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello, Nordic staff,
I work at UART(Host PC_A)<->BLE(S110)<=> BLE(S120)<->UART(HostPC_B) product(like a SPP profile of Classic BT) using a S100 and S120.
I use the flow...
I recently purchased the nRF51 DK and the NRF51-DONGLE. Would you please advise how to use these two devices. My goal is use the nRF51 DK to programmatically control the Reset...
When I call nrf_gpio_pin_set(LED_1), the LED is turned off and when I call nrf_gpio_pin_clear(LED_1) it is turned on. Is this expected behaviour? I can't find any schematics...
Hello,I changed nrf51822 firmware and NrfUart API .Now nrf51822 dongle and beacon can comunicate between them .Beacon transmit notification data and can receive a command...
Does nrf52 SoC consumes the same current at different supply voltages(assuming similar operating conditions) ? For eg what is the difference between operating the nrf52 at...
Hello,
I've just received a new nRF51822 EVKIT and I'm trying to run the blinky project example.
I have installed uVision 5.11.10, the Segger Drivers and the Nordic SDK...
Hello,
I want to use a mobile Bluetooth as a transmitter and the dongle of nrf51822 s110 (pca1000) as receiver using master control panel and just read the RSSI values...
Dear All,
Can we used GPIOTE Channel for Both Task Out and Event IN functionality if yes how can anybody use?
I want to make 15 External Interrupt using GPIOTE module...
I am wondering where I can find the temperature dependent behavior of the ADCs on nRF51822. I observe the ADC readings vary noticeably even when the die temperature reading...
Hi Nordic,
Where is a bug in bsp.h nRF51 SDK 9.0.0 and I think it was were before as well:
LEDS_NUMBER equal 0 causing a compilation error.
In Line 59:
#if (LEDS_NUMBER...
it will try to lower the RF, TX power
Bluetooth is not sure what to do because the first time
What things do I need to solve ? ex)component, software,hardware...
Good morning,
I have already implemented my application based on nRF51822 and SD110 v8.
In what regards bonding, I use a static passkey and it works fine.
The product has...
I will use the functions in app_timer to set a timer to fire every 3 seconds. I want this to occur "forever" (e.g.until a restart of the nRF51).
To avoid a timer overflow...
Hi,
I am using the nRF51-DK board as a central running with ble_app_multilink_central_s130_pca10028 sample application. I am using SDK version 9.0 with Keil 5.14 version...
Hi all! I am using the nRF51 DK and I am trying to use the elements demo APPs that Nordic provide - the Beacon app. after the downloading of the app and watching it working...
