Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
What would we expect the INFO.VARIANT FICR register's value to be with, for example, an nRF52811-CAAA-R7 vs. an nRF52811-CAAA-R7-B?
Right now I am seeing "AAA0...
Hi we are working on a matter project using ncs v2.6.0
Currently we are running out of RAM memory and that´s why we have moved to minimal logging by enabling
Now we...
I want to use 5" inch display for my project as nrf52840 is not able to handle that so I want to FT8xx EVE for the screen functioning? so did anyone has try this or any leads...
Dear support,
I performed a 48 hours- 20°C profiling of my 110mAh battery and managed to get my profile (really appreciate your nPM PowerUP tool. Helping a lot for development...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
Even with the LTK key entered, wireshark cannot decode Bluetooth packets between two paired connected devices I followed this course exactly,but it failed to live up to expectations...
NRFX_TWIS_EVT_GENERAL_ERROR
I am thinking of implementing TWI slave functionality in the nRF52840.
The event handler is written as follows.
Read operations from...
I am thinking of using nRF52832 as both transmitter and receiver, and creating a firmware where the transmitter adds the acquired data to the Manufacturer Specific Data of...
Hi Nordic：
SDK version: NCS_V2.7.0
sample： peripheral_uart
config：
Compile error without any changes：
May I ask how to solve this problem？
best regards！
jermi...
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
