Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello Nordic Team,
We are currently working on a project that has nrf51822 and currently in the production stage. We are facing an issue with Bluetooth getting disconnected...
There is a bug in nrf_bootloader_wdt_init() in nrf_bootloader_wdt.c that can cause all DFUs to fail for long WDT reload values. I found this bug because I'm using a really...
Hello,
We are using nRF52832 to develop a door lock controller. As nRF52832 cannot work as NFC master, we use another chip to read M1 cards. Everything goes well, except...
I was under the impression that when the voltage was 0 in a GPIO pin, reading from that pin would return 0, and if there was any voltage going through the pin it would read...
I found a Q&A that shows 1 channel 2MHz pulse but i don't know how to generate 2 channel GPIO pulse with 2MHz frequency
(one channel is inverted pulse to another channel...
This is a bit of a weird question, but I thought maybe I could get a few useful inputs here.
I'm working on a mesh-like project where we need to facilitate communication...
I would like to switch to using libUARTE for both of my UARTs but I don't have any additional timers free. Is it possible to do this and use FreeRTOS timers?
Thanks,
...
Hi,
We would like to interface with our nRF52840-DK from a PC.
We need to be able to send\recieve data from PC -> 52840 using Nordic's UART service.
We are looking for...
Hi,
We are the company which widely use your products in our devices. Currently we have the nRF9160 based device which have permanent trouble with radios. I want to ask...
Hi All,
Is there a tool or app that shows a visualization of Thread RSSI?
Any help would be appreciated, thanks in advance.
Best,
Tao
Ref:
https://devzone...
Hi,
I am developing both Central and Peripheral devices with nRF52840. For consistency, both are using SDK 15.3.0 and S140 V7.
I am able to connect to peripherals and...
Hi,
I was try to import modul nrfxlib in extising cmake project. My IDE is Eclipse CDT. Version of Zephyr is 2.4.0. Reason to do that, was testing SoftDevice BLE functionality...
We are using our board design using nRF52840.
During bringup I noticed that I could not run the Softdevice and the SPI driver simultaneous. After a bit of debugging it boiled...
I'm trying to send radio frame in timeslot but it's not working. From what I see with an spectrum analyzer, only the first frame is sent.
I am able to make the radio works...
Hi,
We are developing an application with a custom nrf5340 board in which beacons are sent periodically every 100ms. We have been analyzing power consumption with a Power...
