Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Dear ,
I am using THINGY:91, FW: ncs v1.0.0 (#943 from joakimtoe : pca20035_to_master )
I moved to: https://github.com/NordicPlayground/fw-nrfconnect-nrf branch master...
I purchased a module that I encountered during startup. At first I programmed the module via the ST link v2.
Example: E: \ nRF5_SDK_11.0.0_89a8197 \ examples \ peripheral...
Hi,
I have just installed nRF Connect v3.2.0 on my Windows 10 x64 PC. I have an issue using the LTE Link Monitor app.
When I click on the Search networks button, I get...
I am able to program the nRF52832 but not all functionality is implemented.
I had previously programmed the device with a Nordic UART service and then tried to program...
Hi guy,
I am new to nRF52, I read some example code and I see this:
#define SPI1_CONFIG_SCK_PIN 2 #define SPI1_CONFIG_MOSI_PIN 30 #define SPI1_CONFIG_MISO_PIN 4 #define...
Hi there,
I'm currently working on a project in which I need to be able to deactivate Bluetooth advertising at the press of a button. I am using SDK 15.3 and have built...
I am using the database discovery module in my app (my code is based on the "HRS client" that is one of the SDK examples). I am able to discover multiple services (both custom...
To the kind attention of Nordic support team,
I have got legacy nRF24 gzll devices that are supposed to communicate with new nRF52 platform. Sometime it happens that nRF52...
Is board support available for Thingy91 "nRF9160_PCA20035" board in Segger Embedded Studio? I am not seeing "nRF9160_PCA20035" as a supported board under "ncs\zephyr\boards...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi, I using the 15.3 SDK.I want to get the peer's name by filtering Company ID(manu data).The Company ID is in the scan response packet, and peer's name is in the adv data...
Hello!
I would like to use an external antenna with my nrf9160dk to be able to attenuate the signal. But I am unsure about what is needed to make it work.
Is it enough...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
