Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Is it possible to enable the Segger Flasher ARM Targer power supply using nRFutil?
We are now using a Segger Relay adapter , but this needs the Flasher's ARM target supply...
Looking for base examples for a push to talk using this dongle board and GATT. I choosed Peripheral LBS
Other basic example (Beacon, Blinky etc) compiled and work w/o problems...
Hi,
We want to set the PMIC's battery discharge limit via the registers BCHISETDISCHARGEMSB and BCHISETDISCHARGELSB to 1200mA but the nPM1300 PS does not describe how to...
Hi!
We're assessing the EN18031 compliance, and would like to know if there's any plans for product certification with nRF9151?
I found that the certification was...
Hi, I was checking the HAL for SPI in master mode and notice that when pm_device_action_run(<spi_device>, PM_DEVICE_ACTION_SUSPEND); the CS pin isnt changed since it status...
I want to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.2.0, to hopefully get the wifi WPA Enterprise functionality to work. This is an existing...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following error message:
fatal error: nrf.h: No such file or directory
"nrf.h" is now located...
Hello, I'm using Nordic Central HR example. I'm wondering how to read RSSI of a BLE device connected to the NRF5340, I have tried multiple version found on this forum, but...
Howdy,
I am trying to connect a Waveshare BME280 to my nrf9160dk, and it's not obvious which jumper goes where. The documentation states:
Wire color
Sensor board...
hi,
i'm new with the nrf9160DK so can you please guide me to how can i start and config my nrf9160Dk with my laptop from scratch because this video is not helping me https...
Hello:
I created an app.overlay. Here it is:
/ { aliases { fra_sw = &fra_sw0; }; fra_sw0: fra_sw0 { gpios = <&gpio0 0 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; label = "FRA_SWITCH...
Hello,
We have a dual-purpose connection in our design where the signal can be either an analog input or a digital output. We have done some testing and can see that we...
Hi and Nordic forum
Please find the attached summary on the issue we are facing and help us get the guidance regarding the same
We are developing a Zigbee-based device...
Hello,
I am evaluating the nRF54L15DK current consumption based on Nordic example: https://academy.nordicsemi.com/courses/nrf54l-series-express-course/lessons/lesson-5-development...
