I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I am using Nordic nRF52840 (nRF5SDK v16.0.0) and softdevice : s140.
Nordic MCU is connected to Host MCU over UART interface (baudrate = 115200). I have below observation...
hello,
i am using nrf52840 with sx1276 i am trying to change some of the calls from arduino to nrf52840 can you tell me i am doing everything right
#define DIO0 NRF_GPIO_PIN_MAP...
Hi. I use NCS SDK 1.5.1 with NRF5340 .
I took the project from: \zephyr\samples\portability\cmsis_rtos_v2\philosophers\ as base and try to add two additional tasks.
Application...
Hi,
I would like to implement cell triangulation with the nRF91 in order determine the location of the device via cellular. I already had a look at the available posts such...
Hi friends:
My ble mesh gateway want to remove a mesh node
(a): Which api can i use to realize this purpose?(My SDK is nrf5_SDK_for_Mesh_v5.0.0)
(b): There is a special...
Hi Community! We're happy users of a range of Nordic solutions on behalf of our clients in Europe. Now we're facing a new challenge: one BLE device that should act as a sort...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
Hi. I am a beginner with nrf52840. Trying to get SPI and an I2C peripheral working at the same time using the SEGGER Embedded Studio. I have working version of both the I2C...
Hello,
I am using the nrf9160 to develop a cellular product but am seeing inconsistent end-to-end connectivity results. For the nrf9160-dk and a custom board based on the...
Some transciver can improve RF performance like output power and EMV, through supply higher DC voltage. Did nRF52840 have the same characteristic with BLE? Is that high votage...
Hello,
I have a questions on the ADC and GPIOs front end input resistance over operational temperature range, as our final product operating temperature shall well beyond...
Hi,
we are developing a custom board based on nrf9160 that include CAN bus. When updating nRF Connect SDK from v1.4.2 to v1.5.0 we can not get CAN-bus up and running again...
Hello,
For our device we are using a NRF52832 and SDK version 17.0.2. It only has one Button connected to P02. Due to needing the device to be water resistant the decision...
