I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello ,
When i am using sdk functions with freertos some of the callbacks/functions requires (for example) xTaskNotifyFromISR() instead of xTaskNotify .
So how can i decide...
I am going to mass-produce beacons with built-in ble uart app sample.
However, I am not sure those produced beacons will have unique mac-address.
In my view, those are...
Hi all i am trying make a communication between esp32 and nrf52840 using UART. Initializing the uart driver was proper and pins also correct. when nrf start transmits then...
Using nrf52810 SDK 17 ble_app_hrs for my example, and i add some code about the passkey
Now the situation is after I enter the passkey on my Iphone nRFconnect app, and if...
As with my recent inquiry about a softdevice assert at PC=0x24e70 , I'd like to know which assertion fails in softdevice S132 version 7.0.1 at PC=0x157ec.
Is there a table...
Hello,
I observed a weird behavior when I changed to nRF52840-DK from nRF52840 Dongle. I am using the device as an SPI slave connected to a Raspberry PI as SPI master. ...
While trying to execute the light switch example, i was able to set the nrf52840 as evaluation board as proxy server but failed to do the same with the dongle.
2)When...
Hi,
When running the at_client example, I send the AT+CFUN=1 command via the LTE link monitor. After a few seconds, the nrf9160 reboots.
I want to say that before my program...
Hi all,
Currently I am working on my first project with the nrf52832. All is going quite well, but I would really like some help with my flash layout, basically I got some...
I'm attempting to control the microphone level from Windows 10 and Mac OS by configuring a Feature Unit.
The USB audio example demonstrates how to configure a feature unit...
Hi,
I am using the uart example from https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c
I want to read serial data from...
I'm making my own protocol on nRF52832 devices and I'm wondering if there's any possibility to have data corruption when CRCSTATUS contains CRCOK value.
I'd like to get...
hi all,
I am using the following example:
"..\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart_adc_scan_mode" to send via bluetooth data coming from ADC. ...
Hello, team.
Thank you for helping.
I was wondering that what is the difference between 'managed flooding' and 'relaying' in mesh.
The only one that I know is provisioning...
Hi,
I am just a beginner in this field and need support to proceed.
I want to have a BLE Mesh network using lights, switch and occupancy sensor. In this I want to use...
