Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi i am new to learning Nordic SDKs and I am working on adding custom commands to a BLE example using Nordic UART Service ( here ). I tried to apply this concept over to the...
I sent the AT instruction back correctly with the serial tool sscom5.13.1
I sent the AT instruction error with the secondary function: at_cmd_write ("AT-CGDCONT?," buf,...
1. When using SEGGER Embedded to use Chinese comments, the cursor display will appear abnormal lying each time Chinese characters will move the cursor only half a character...
This is a voltage drop of 3.3V to ~450mV before decaying.
I'm using P0.02 (AIN0) on the nRF52840 on a custom board. This is my config:
My handler function is never being...
Hi,
I am working on handling multi-radio protocols like only 1 radio at a time. ( https://devzone.nordicsemi.com/f/nordic-q-a/63194/when-the-timeslot-extension-could-be...
Hi,
I am trying to disable writes to certain regions of flash memory. But different from the nRF52840 Product Specification, NRF_ACL is missing the DISABLEINDEBUG register...
Hello,
I'm trying to connect a bluetooth device (peripheral) with Web Bluetooth (central). I send an addvertising packet and I can see the device in Web Bluetooth but I...
Hi,
I just bought an NRF51-DK which I want to use with MBED. I need to download the CMSIS-DAP firmware for this board but cannot find it on the downloads page for this DK...
Hi,
i am trying to create a new model for mesh SDK 4.2.0 i am using nrf52832 please provide link or any document for creating new model, i found a link which is for SDK...
I have been using the nRF5 Mesh SDK for development and am in need of implementing single press, double press and long press on the nRF52832. I have seen the nRF5 SDK for...
Hi,
I get the error "[DFU] Remote DFU error: INVALID OBJECT. SD busy? Retrying...." when attempting a firmware update over Bluetooth.
The bootloader, application and the...
Hello,
I'm working on nRF52811, SDK16.0, Softdevice 7.0.1.
Using the pwm_driver example in the SDK, I'm trying to run a simple PWM for an RGB LED. Following is my simplified...
Hello,
I am trying to develop a product on a large scale. I need the last 4 digits of DEVICEADDR[0] as the advertising name for uniqueness. But I am not able to get it working...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
