I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
getting error in running bootloader
Output/secure_bootloader_ble_s112_pca10040e Release/Obj/nrf_dfu_validation.o: in function `nrf_dfu_validation_init':
I have designed a custom board with the nRF52840 following the examples from the dev kit, dongle, and datasheet (circuit config 5). The board is similar to the dongle but...
I understand that the BLE-stack takes the highest processing priority on the nRF52 (nRF52840 in my case). So data read on one of the GPIO pins of the nRF52 may be "lost" if...
Hi guys , i'm using nRF mesh library nRFMeshProvision 2.2.3. I'm trying to connect to multiple mesh nodes and send message to all of them. In provided class NetworkConnection...
Hi all,
I am interfacing with an MCP25625 device using SPIM3 on the nRF9160 and I am receiving no response on the MISO line. I have verified the correct functionality of...
Sorry i post on 2 thread. I don't know how to delete this post.
So i modify and add the main link:
devzone.nordicsemi.com/.../total-discuss-tx-power-change-on-nrf52811...
I would like to understand the timeout values for wait for acknowledge on ESB protocol
Example, from the source code:
#define RX_WAIT_FOR_ACK_TIMEOUT_US_1MBPS (73) /*...
Hi,
I'm a firmware eng with an ancient history of h/w design.
We are in production with the nrf52840 but still do new designs.
This question is in reference to the 52840...
Hi, We were trying with a new n/w carrier in Canada ( Maxim ). nrf9160 is able to connect to the network, but it is not able to resolve our server URL ipv4 address. Below...
Hi,
I am testing RX mode.
And the module is sure to enable M1 (%XSYSTEMMODE: 1,0,0,0)
I use the following command, but return error.
AT%XRFTEST=1,1,2,19500,17,1,0...
