I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I would like to calculate maximum range between two devices equipped with nRF52840 transceivers working in the IEEE 802.15.4 radio mode. Can I assume that -100 dBm...
Hello,
I have a question about Bluetooth connectivity issues. The BLE code I'm trying to make will be connected to the smartphone (Android). If phone out of the Bluetooth...
I'm developing a bluetooth device that only advertises data, it's set to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE and BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hello everyone,
Can I use the latest nrfutil 6.1.0 tool to generate the DFU zip file for the dual_bank_bootloader in SDK11?
If yes, do I need to keep the --hw-version...
Hi, I wanna enter the system on sleep to save the power up to 10uA(about tens of A). I am using nrf52840-dk with SPI LCD and some GPIOs in zephyr. Also I want to do DEVICE_POWER_MANAGEMENT...
Hi, I would like to run an nrf53 example project. I got the devkit, and after some struggle I am now able to compile and run a project.
I need to run an Bluetooth example...
This is really a question about best practice - I have some ideas of ways to do what I want, but wonder if there is some clean API-supported method that I haven't found.....
Hi, I am in design stage and i need to change nrf 8001 to nrf 52810. In this point i have a question about pin configuration in nrf52810, Can i use any pin for any use? i...
Hello everyone.
I know from Errata document that the GPS antenna soldered on DK is not working properly on the 0.8.2 version of the DK. I need to use GPS for time syncronization...
Hello,
We are allocating a large amount of pages (100 pages, ~400kB) for the Flash Data Storage module in order to hold collected data. As a result, the fds garbage collection...
Hi all, can the nRF52840 dongle be used as an external Bluetooth 5.0 peripheral via a Raspberry Pi 3 running Linux?
I received this message from my engineer
' The drivers...
This is based on the article fround in devzone here .
I'm compiling a simple Hello World and followed the instructions as per the nrf Connect SDK Turorial Part 2 .
To...
Howdy,
I'm using Zephyr to configure an nRF52840 to act as an I2C master and send data to a TM4C slave at a 100kHz clock rate. The nRF52840 appears to hang after calling...
Hello, I am working with nRF5 SDK 17.0.0 and using IAR Embedded Workbench 8.50.1. I am following the Secure DFU bootloader guide as posted here .
On Step B3, I get a build...
During development, it is a very common task to combine the 4 elements into a single hex file, softdevice, bootsettings, bootloader and application. Mergehex is limited to...
