I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
I faced a problem while building my project. Please see screenshot below
I think I have already include all the files and everything compiled. But this error shows...
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
I am working from the ble_app_hids_keyboard example. To support multiple centrals, I imagine the first step is changing NRF_SDH_BLE_PERIPHERAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am trying to set up eclipse + gdb + openOCD for debugging zephyr 2.0.0. applications on nRF52832. Following the official Zephyr documentation build-and-run-an-application...
Hello,
I am using NRF52832 with soft device 13.0.0 and Nordic's bootloader from the examples.
What I do is develop an application which stores some values in uicr registers...
I'm using 52810 with s112 stack.
And I need two PWM channel with different frequence. one channel set to 4KHz to cotroller BEEP, the other one set to 15Khz to control...
