Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
Hello,
We are currently using a Raytac SoM that has nRF51822 SoC with Adafruit UART firmware. We are running into two different scenarios BLE connectivity issues where the...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
