after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have 3 devices that can communicate via UART: 1) nRF52840-DK (PCA10056) 2) FTDI (set to 5v logic) 3) BLE HM-19
I'm using the example in ./nRF5_SDK_16/nRF5SDK160098a08e2...
Hi,
In gps sample, the prj.conf file is:
And I can use Putty or Serial.app (on my Mac) to view the output
In our application the prj.conf file is the following:
...
nrfjprog is reporting "Cannot connect to J-Link." while trying to erase on MacOS Catalina
Board used to work properly, but attempting to re-connect after a wipe of my MacBook...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
Hi!
My goal is to sample an ADC channel with 10 kHz sampling rate and acquire 2000 samples in one samples acquistion and then return to lowest possible power state. This...
Hi,
I received a Thingy91 from a colleague who orderd it shortly after hitting the virtual stores but didn't do a lot with it. I got it on my table and started to work on...
Hello,
SDK 15.3.0
s140
nrf52840-DK
IDE: SES
I am attempting to use the LPComp + NRFX TIMER 4 to count the rising edge of a signal, the timer is being used to time...
I am currently evaluating the nrf52840 for a possible future application which is based around BLE and should also provide a HID Generic interface to perform communication...
hi..I have merged the saadc with ble_app_uart and i have added all the respective files and enabled the ppi, saadc everything . while i am running the code ,getting unknown...
Hi,
I noticed something strange while developing with the nRF9160 modem's RTC. Here's the sequence of events
Connect cellular
Get time from NTP server and initialize...
Hello nordic
I'm running iot icmp example on my nrf52832.
The border router is Rapberry 4. root@raspberrypi:/home/pi# uname -a Linux raspberrypi 4.19.71-rt24-v7l+ #2 SMP...
Hi Nordic Support,
I am not getting sensor(VL53l0X) value,i used slave device address=0x29 and register address=0x01. I am getting starting distance value=255,afterwards...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and...
