I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
So as far as I can make out, when I load a new application into the flash, the NRF52 will attempt to first load a secondary memory space and if successful, it will then replace...
Hi,
Right now i am using Blinky example in Peripheral section of SDK15 (S140). I would like to enable Coded PHY (BLE_GAP_PHY_CODED) instead of default setting (BLE_GAP_PHY_1MBPS...
Hi, I have problem with timer in nrf52810. My TIMER2 counts very slow. I declared it as NRF_DRV_TIMER_INSTANCE(2); and config struct is:
.frequency = NRF_TIMER_FREQ_16MHz...
Hi ,
I can compile and use the UART example but when I try to use it in my project I get some linking errors
I have copied and past all the sdk_config.h file to my project...
I am waiting for my custom pcb based on the nrf52832 to be ready and I want to test the flashing process. Is it possible to program a nrf52 DK with another nrf52 DK using...
Hello,
I was wondering if there is some way to program a device to act like a BLE slave, which would sleep and periodically wake up to stay in receive mode for a certain...
Hello, I'm confused what the NRF51422 uses for it's digital IO reference. So for example, If I use a 3.0V coin cell battery through its DC/DC converter: 1. What voltage does...
I download the SDK at https://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK/nRF5-SDK-zip/59011 . When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c...
Hi,
I am using SDK10---->ble_app_uart--->pca10028--->s110 for non-invasive GLUCOSE measurement. I checked nrf_adc.h file & used adc_sample = nrf_adc_result_get(); for getting...
I am using nrf52832 development kit and softdevice v5.0.
I am using this code which I have attached.
I have added all require files.it might be not showing to you because...
My current setup is this:
I have a nRF51822 beacon (tiny coin cell beacon) advertising with its default settings. I have another board, a nRF51822 Development Kit, that...
Hi,
I have a customer request regarding ISP1507 module (with nRF52832 integrated) and battery information.
Customer want to have battery information using LED (bicolor...
Hi,
We are using nRF51822, SDK12.3, pca10028, S130 with "Red Bear BLE Nano V1.5" board. We try also in nRF51DK and our own board (designed by us) and the issue is the same...