Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm trying to use the SysTick timer on nRF52 to time some various tasks for debugging. I configured it like so, which I expected would cause SysTick_Handler to be called...
I didn't find any documentation in the peer manager for the need of this write buffers.
I do understand, that peer device data is stored there before written to flash. But...
Dear Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210 v5.0.0
I have 3 devices: two masters (No. 1 and 2) and one slave (No. 3). In my application, I pair the...
Hi guys
I have one nrf 51822 demo board.
And I want to buy one more board as BLE sniffer.
Can I use a nrf52832 demo board as sniffer to grab packet between phone...
Hi guys
I am programming nrf51822 demo board with sdk11 and try to finish service tutorials .
I finish all step in service tutorials and try to get service information...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
Is there a problem logging into Nordic site ?
I have tried resetting my password and it doesn't seem to work. Had posted a question in the this thread earlier
Dear Nordic team and community,
Have you encountered the problem where standard BT4.0/4.1 GAP Peripheral device would be "blocked" from connection (kind of "denial of service...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...
Hello everybody!
I have one nrf52840 DK and nrf528323 DK. I was flashed and test throughput example. I reach 450kbps. ( transfer 1Mbyte in 18s). Can I enhance this speed...
Hi,
We are interested in nRF52840 and we know that nRF52840 supports both on IEEE 802.15.4(Thread, ZigBee) and IEEE 802.15.1(BLE).
However, does nRF52840 can run BLE...
