Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
Hi
I am getting some weird response from my nRF51-DK.
Situation 1:
When I try to flash it with the Blinky code (\sdk11\examples\peripheral\blinky\pca10028\s130\arm5_no_packs...
I'm trying to under the ble_app_multirole_lesc project and I'm a bit confused about calling sd_ble_auth_key_reply and sd_ble_lesc_dhkey_reply. If you are using Just Works...
Hi,
I am trying to send a HEX command to a device over UART at 9600bps using nRF52 DK, but it never works. However, it works with Arduino (so the receiving device should...
I have nRF52 Development Kit,after my first time programming the Firmware to my board.I can't erase or program it any more?
The nRF52 Development Kit can be connected with...
Hi,
I have read the following posts and understand how low clock frequency mode can be selected
devzone.nordicsemi.com/.../
I've also read in many posts that 4s calibration...
Dear Sir:
Could I use the external reference AREF1(pin0.06) instead of internal VBG 1.2V for ADC operation ?
I do the following settings to config using external reference...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
Hello,
I'm trying to write value to a specified address with ble_flash_page_write .
I'm using ble_flash_page_write after ble disconnect event. I've tested different...
hi Ole BAUCK, my slave device is STPM33 ENERGY METER using this device we can calculate vrms,irms,real power,reactive power,energy and many more.. that device is not having...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. Now it almost works. But after an app image has been successfully transferred...
hi all,
i am using sdk v8.
i want to transmit the address through uart and read the data using UART.
i am using app_uart_get and app_uart_put api's.
PROBLEM:
if i connect...
Hi, it says that I have to put my beacon into beacon config mode in order to configure beacon device through the app. How do I enter beacon config mode in my nRF51dk? When...
