Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I have implemented the ble UART service in the s120 example : ble_app_multilink_central. I can receive messages that are sent from a ble UART peripheral in the ...
I'm trying to use the bond manager to store links.
I used the ble_uart application posted in this site by a Nordic employee and tried to use the bond manager as it was done...
Hello,
i can't find the characteristic read timeout in BLE Core SPEC 4.0. If the central device read a characteristic from the peripheral device, in which time the peripheral...
Hello
I have uploaded a hex file which for some reason I cannot see the tag anymore, is there any way to re-program, erase or reflash the beacon kit using nrf51 programmer...
i was trying to implement bonding in ble_app_hrs example(SDK V6.1.0 and soft device v7.0.0)
i have given params
#define SEC_PARAM_TIMEOUT 30
#define SEC_PARAM_BOND 1...
I want to use the Smart Beacon Kit (PCA20006) and the blink led demo. However it seems that I cannot use the s110 V76 softdevice when writing my app in Keil. However, how...
I'm writing an application which updates the ble advert data at run time. I use the radio_notification callback functionality. Inside that function, the code calls the ble_advdata_set...
Hi, I'm trying to run ble peripheral and timeslot receiver at the same time. I can see ble advertisements and I can connect to the peripheral. I can also read and write ble...
Hi,
Some questions below about the HID keyboard that refer to the example "/s110/ble_app_hids_keyboard" .
What initialize m_advertising_mode value before to call...
Hello,
to reduce ernergy consumption i use the sd_app_evt_wait() function while the twi is sending or receiving data.
i set nrf_twi->address and nrf_twi->txd and set...
Hello,
I have troubles using spi_master_example.
I want to control by spi a slave device from the nRF, I am sending sequences as expected and my slave device answers me...
The S130 SDS 0.5 documents a CODE_R1_BASE of 0x00020000, but I can't get it to work with code at this location. Any SoftDevice API call ends up in the application's SVC_Handler...
Hi,
i use the library app_gpiote to setup interrupts on a toggling external pin(this pin generates a signal which changes from high to low).The external interrupt signal...
Links: ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works.The ble device call disconnection,but ble android phone respones it more then 5s...
