I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to change the name of the USB port in the "usbd_ble_uart_freertos" example code. Currently, it shows up in the Device Manager as "USB Serial Device (COM12...
I am developing a simple BLE mouse using ble_app_hids_mouse of SDK17.1.0. I found out through devzone that left mouse button click sends (1, 0, 0) and right button click sends...
I'm unable to load values into characteristics—they show up as N/A on the nRF Connect app. I tried to enable notifications using the Client Characteristic Configuration, but...
Hi Nordic Community I have a problem with the PAwR examples were I'm unable to place a sync interval bigger than 2 secs.
The example starts with an interval of 0xFF * 1...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi team,
We need to interface STM32L4(Host MCU) with WT02V40V in our design.
Is UART communication enough for interface both?
And also, Is CS pin common for SPI and...
Hi Support Team
We want to use nRF7002 and nRF54L15 to implement Wi-Fi, could you provide us the hardware reference design of nRF7002 work with nRF54L15 ? Many thanks.
Hello Everyone,
I am designing the BLE peripheral which is connectable, we have our own BLE mobile application. I am trying to configure the peripheral to be visible to...
I am attempting to compile the nrf sample code for peripheral uart and I encounter a fatal error in the extensions.cmake file. Apparently the CACHE_VAR_REQUIRED is set somewhere...
Hi,
I uninstalled my VScode earlier for some other reason, and when I reinstalled it and upgraded toolchains and SDK to v2.7.0, I found that my VScode couldn't find my board...
We are developing the project ARGO .
At the current stage ARGo is going to Support NB-IOT communication
A mother board is under development to support the mini-PCI card...
Dear Sir/Madam
I have installed the Jlink driver and nRF sdk for 9160 on my macbook.
I use the nRF Connect for VS code to program, but I can't see the device under the...
Hello,
I'm trying to get some basic SPI communication between the nRF91 and nRF52 chips on the nRF9160DK. We have been using UART for this communication however we want...
"The nRF52840 is developed using NCS v2.6.1. When the ADC is set with the reference voltage as (.reference = ADC_REF_VDD_1_4, .resolution = 10), the ADC sampling output is...
Hi,
I am updating a relatively old project using SES. I am using nRF5_SDK_15.3 with S140 on an nrf52840 target (matches the nrf52840 EVK).
I have been developing and have...
