before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
When I try to build the solution with "Optimize for debugging (-Og)" the linker fails saying `rodata' will not fit in region `FLASH'. FLASH overflowed by 46056 bytes. This...
Hi all.
I have a project on nrf52840 with ble. I needed to add a nrfx timer there. I deleted everything from the main function. Added the code from the timer-counter example...
I'm going to add frequency hopping to ESB
so i have some problem
1、Whether demo is available for learning.
2、for example Gazell frequency hopping ,Where can I see detailed...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
Hello,
I am starting with the nRF Connect. I got a nRF52840 DK and I am following the 'nRF Connect for VS Code' YT series.
I got as far as part 5 (debugging), but I cannot...
Hi all,
SDK: NRF Connect v2.5.0 We've made a custom PCB with the NRF9160, and we have made a custom board configuration for it.
Our issue seems to appear when trying to...
Hello,
I have a mosquitto broker running on my pc. I want to connect and published to this broker through nrf9160.
The issue that I am facing is that prj.conf file only...
