My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
“Why, after setting up the custom board and writing CONFIG_BOARD="my_custom_board" in prj.conf, do I encounter the errors: message(FATAL_ERROR "command failed with return...
I was hoping to access content from DevZone and DevAcedemy content from NotebookLM to combine with my private documentation so I could ask questions specific to my device...
I have been developing software, embedded systems, and hardware for over 30 years, and I must admit: working with nRF Connect + VSCode on Windows (both native and via WSL...
Hello,
I'm experiencing FAT FS corruption (files disappear or files disappear + "volume is full" error on any file write), when I'm unplugging my USB cable. Here is my environment...
Hi everyone! I've recently run into some issues with Bluetooth development, and I'd really appreciate your kind help.
1. Hardware & SDK - SoC: nRF54L15 - SDK: nRF Connect...
Hi, In have the nRF54L15 in System ON IDLE. I can see that enabling WDT31, set up so that it is paused in sleep mode (CONFIG register = 0x4) causes a current increase of ...
Context : SDK2.9, nrf9151
Here is the crypto configuration we had
Our product use MBEDTLS1.2, this is why CONFIG_MBEDTLS_USE_PSA_CRYPTO is set to False.
We are able...
HI.
Environment : ncs v3.0.1, nRF54l15 DK
I have a project to use Multi Role of BLE.
peripheral advertise 300ms period.
central scan 2m 30s period. ( actual scan...
I have made a bare metal app using gcc on Linux for the nRF5340 Audio DK. I'm able to start the segger gdb server, load the code, set a breakpoint, run and watch the LED's...
Hello
In the past I was able to run DFU on both SDK 17 and SDK 14.
Now I am developing over SDK 17.1.0 a new application and attempted to run secure DFU Bootloader using...
Hello, I am working with nRF52832 (PCA10040 DK) on nRF5 SDK v17.1.0 with SoftDevice S132 v7.2.0 . I started with the ble_app_uart example and added a custom BLE service ....
Hello everyone,
I have some questions regarding the registers of the nPM1300 specifically for the load switches and LDOs.
In the data sheet in chapter 6.5 under "Load...
Dear Nordic team.
I am a beginner learning to connect a SPI devices with nRF54L15-DK but the program always reports errors. Here are my related codes:
nrf54l15dk_nrf54l15_cpuapp...
NCS SDK and toolchain: nRF Connect SDK v3.0.2
Boards: nRF52DK-nRF52832 , nRF54L15DK-nRF54L15
Issue:
After un-initializing and then re-initializing MPSL, MPSL no longer...
Hi,
We are using the nRF Device Manager app (Android) to update firmware over BLE to the nRF54L15 DK, and it was working fine until August 26, 2025, when the app was updated...
