I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
Hi,
I'm using NRF52840 and having a lot of issues with hard fault.
From time to time, I get an application crash with the following log:
HARD FAULT at 0x00000000 R0...
This question may be better suited for the Zephyr forum, but I figured I would ask it here as well in case somebody can easily see what I may be missing.
I am trying to...
I am attempting to use the UART peripheral with a UART device which communicates via 1 start, 7 data, 1 even parity and 1 stop bits.
Is there any? way to configure or fake...
According to this post it seems clear that a peripheral device cannot set the connection event length in a given connection (and only has mild influence on the connection...
Hello,
it's been a couple of days that i have a problem with NRF9160DK.
The problem is related to function getaddrinfo() that is now permanently returning -11, whatever...
Hello,
I wanted to interface LCD with nrf52840, for that we have selected few of them from different vendors. I was looking for display drivers for LCD, but couldn't find...
When building the zigbee network_coordinator example for the nrf52840 dongle the merge.hex is linked to start at 0x0 in flash so the nrf connect programmer won't flash it...
Hi everyone：
New to the DevZone, nice to meet you guys.
I have an problem to the GPIOTE.
I'm now using an AFE4404 to calculate the heart rate and heart rate variability...
Hello, teams!
I'm sorry to bother you.
Now I'm testing mesh function.
I have two questions.
1) Is there good way to show the performance of relay operation?
...
Based on nRF52840 datasheet, to configure the QSPI peripheral, it is necessary to activate the external flash memory interface using ACTIVATE task. Our problem here is, during...
