I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi i was trying to add nrf calender part which i found in git hub for nrf52 chip with ble app uart example, but when i nrf_sdh_enable_request() called to initialize ble system...
Hello
I want to install the nRF Connect SDK (v3.4.1) on my Linux Elementary OS 5.1.6 Hera to use the nRF9160 and the Thingy91 later on. I've installed the toolchain and...
Hey,
I am working on S130, nRF51, been working for a long time with DFU and it was fine both using nRF Connect and nRF Toolbox
Lately I changed my workstation and so...
Hello everyone I am trying to program my dongle with the Dk Following this schematic :
When I press the reset button on the dongle, the led start pulsing in red.
I am...
someone that can give me a datasheet of this microcontroller (i think) i searched the hole web and don't find one in specific, the one i found are different in the last line...
Hello, I am working on low power modes of MCU M33 core in nRF9160 SOC.
From the document of nRF9160 product specification v1.0, understood that there are two low power modes...
Hello,
I am trying to capture the advertisements of the surrounding BLE devices with NRF52840 Dongle using pc_ble_driver_py python library. I am successful in capturing...
I am working on third party module RAYTAC MDBT50Q-DB with nRF52840 with SDK V17.0. I am trying to run ble_app_interactive example on it but just can't get it done. I have...
Hello,
I'm using the light_switch example for my application and I've integrated my custom model into it. I want to learn which address the server and client respond/publishes...
Hello,
I want to give user defined hard-coded OOB Number in this example for generic on-off Client-Server code, for provisioning both client and server node ( nrf52 DK ...
Hi,
We use mdbt42v(nrf52832) to design a custom board and we encounter a strange issue.
We use ain2(P0.04) to measure a Variable Resistor value, the code working fine...
Hi,
I am using an NRF52832 device (Peripheral) and I have a requirement to transmit around 4kb of data every 100 ms to a Central.
Can you recommend the correct example...
Hi,
I tried building both with cmd line and SES but I get always this error:
/usr/local/bin/cmake -GNinja -DBOARD=thingy91_nrf9160ns -DBOARD_DIR=/Users/dariofanciullo...
