Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
I have a question about setting the gpio pin status. From the picture, it seems that the value on the right represents the status of the gpio pin. So the default value...
I'm using NCS 1.4.0 and 2 boards nRF5340PDK.
I'm using central_uart and peripheral_uart samples. Both display when connection interval change.
The central_uart use BT_LE_CONN_PARAM...
can You explain
light_lc_client_light_onoff_set(&m_clients[0], &set_params,&transition_params);
This command in the lc client used to make the immediate on the server...
I'm implementing a project that attempts to change the TX power of itself during runtime. I have used the set and get functions from the Zephyr sample: https://docs.zephyrproject...
Hi guys, Do we have an outlook on silicon in which errata bugs 174, 195 & 198 (SPIM3 bugs) are solved?
Best regards,
Casper van Doorne
Pink Fluffy Unicorns BV
I am trying to make the LSM9DS1 connected with the nrf52840,
1. Now I am trying to send the hex array to the lsm9ds1, seems always failed.
any suggestion how to make...
Hi,
In my aplication, I bring my nRF52840 into power system off mode with s d_power_system_off on several different events, most notably the BLE_GAP_EVT_DISCONNECTED event...
Hi Team,
We have developed an application where we are able to receive scan request notification in peripheral and scan response notification in central.
Is it possible...
Using the nRF Connect SDK from Nordic Semiconductor is a terrible experience. One reason it being unreliable with many broken samples. And another being the Segger Embedded...
HI,
I'm using Nrf52840 device and connecting my mobile.
After inserting the authentication code for the pairing process.. phone connects successfully and after a few seconds...
Hello,
I wanted to confirm my understanding of the Replay protection cache. In the code, the limit is set to REPLAY_CACHE_ENTRIES and there is a note that says:
@note...
Hi to all.
I am new to this forum and to the Nordic range of products.
My experience over the last few months have been with arduino and Feasycom bluetooth modules. I...
Hi,
Since I updated nRF connect from 3.6.0 to 3.6.1, I get this error when I try to connect to a device :
"Error when getting device info: Error: Error: Error occured...
Hi,
I'm trying to devise the hardware platform for a Home Monitoring medical device. In the first place I planned to use the NORDIC nRF5340. With its large memory it would...
Hi.
We have a debug board for the NRF52832. The breadboard on this board is working fine. But if NRF52832 is used outside the debug board, then for some reason, some phones...
