Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are having some EMI issues with USB full speed and would like to force the nRF52840 USB controller to operate in USB low speed mode. Is it possible to configure the...
Hi
I use the following script to program my boards which takes 20 to 30 seconds to complete. But recovery and programming done through SES for the same code is much faster...
I'm using nRF51 BLE dongle as a sniffer and trying to capture BLE packets through CLI. I'm using example.py which came with nRF sniffer software.
I unable to get the list...
Hi team,
My customer wants to read the BLE address (random address that is generated by nRF52) to generate a QR code for quick pairing in their application. Do we have any...
What data do app and BLE 2 generate when pairing and binding on the app and BLE devices? Can I get it on the APP side? I know that LTK, STK and other data can be obtained...
Myself Sheethal Sunny, Design Engineer- SFO Technologies.
Our main proposal is going on for newly deign product.
May I know any Bluetooth module is supporting similar...
Hi,
I am searching for a clean way to handle a timeout (because I2c device does not respond or there is a hw issue with the I2c bus).
On startup I probe different I2c...
Hello ,
I am interfacing the customized board nrf52832 , As of now we didn't populated the 32 MHz externally . so I am trying to program the peripheral alone. Twi sensor...
Greetings,
We developed a customized board using NRF52832. We flashed the code using NRF connect JTAG. The LED is working fine. But when we flashed the BLE_UART BLE is not...
Fired up nRF Connect v3.6.0 on MacOS
Plugged in new 9160-dk and switched on.
Connected to USB.
Selected board. Green dot appeared but nothing in the "Device memory layout...
Good morning,
We have developed a prototype based on the nRF52840. We have also developed an Android application.
When smartphone has device already bonded the application...
Hi,
I am a beginner in BLE Mesh. I am trying to create a Mesh network for residential purpose using Tuneable lights, switch and sensors.
Mesh SDK version : 4.2
On the...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see below API for initializing/updating advertising data.
I want to know what does it do with the buffer...
Hello
I am now quite familiar with the basic PWM playback capabilities of nRF52832. However, I would like to make a chain of simple and complex PWM playbacks.
I have already...
Hello,
I am developing an application that sends data from an Arduino Nano 33 BLE Sense to a custom Android app (Motorola Edge running Android 10). The Arduino board is...
