Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
Hello,
I received information that i could turn the modem on and off not more than 60 times within an hour.
We are however working on a real time system, which may...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
I have a custom characteristic on which I send ASCII strings as notifications similar to NUS. Is there a way to have the Bluetooth Low Energy app in nrfConnect show the data...
I am writing a BLE application on the nRF52832 using S132 v6.0 and SDK 15.2, and my application is using the nrfx_SPIM driver. I find that once I initialize the spim driver...
I am using the nRF52840, SDK 16.0.
I'm attempting to advertise on the coded phy and the 1M phy simultaneously. This works.
I have two phones, one that supports coded...
Hi,
I tried to enable the CMSIS in my CUSTOM Project but I see the following error and the CMSIS configurator is empty. Please guide what would be the possible problem....
Hardware: nRF52840 DK
SDK: 16.0.0
FreeRTOS: 10.0.0
I am attempting to use UARTE1 for a Modbus port. UART0 is already in use for a Command Line Interface. I can set up...
I use Nrf52832 and sdk16.0.Use I2S play sound.
If use:
int16_t sine_table[]= {0,0,23170,23170,32767,32767,23170,0,0,-23170,-23170,-32768,-32768,-23170,-23170};
NRF_I2S...
RTT is a very strange beast. It looks that, depending the printed binary content, the output in the viewer can be displayed - or not. It seems that the rtt viewer acts on...
Hi,
I have converted a project to use the nrf52833 (SES SDK16):
I get a fault with the following:
The build seems to still link to nrf52832_peripherals.h not...
