Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
Hi,
I'm evaluating the Raytac MDBT50Q devkit, using nRF52840-DK to program it. I'm testing the system with SDK project nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c...
Hi. I am currently evaluating nrf9160 on a Thingy 91 board and have the environment for the asset_tracker application up and running.
I want to be able to handle JSON messages...
Hi,
I would like to have a system such as follows:
Taking sensor data storing it locally till around 100 samples (Once per second)
Log this data to the SD with a time...
Hello,
I was wondering if there are production ready fully pre-certified modules for the nRF91 Cellular chips? Like what Rigado (u-blox has it now) made with the BMD series...
Hi,
I would like to use the nRF52840 dongle to connect to 8 devices using Ant+ and to around 8-24 devices using Bluetooth.
Is there a maximum number of devices of Ant...
Hello to everyone,
I've just started playing with NRF52 DK (NRF52832 SoC). It is my first time with ARM MCU. I've had prior experience with atmega328p and MSP430. Although...
Just ordered 2 Thingy52 and could only connect to one of them. Both boxes mention 1.1.0 2019.34
I used the code from https://github.com/NordicPlayground/Nordic-Thingy52...
I change the BLE SDK temelate example using this www.novelbits.io/.../ . In this I added 1 Custom service and 2 charactersitc. After compiling and running this got below logs...
