Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am working on developing an application where the app layer tries to throw out messages if the message parameters are not valid. One the parameters to validate is a TID...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Does following...
In order to compile against custom hardware, we changed overlay and dts files, but I cannot remember which. How do I find out?
I get the error
devicetree error: 'ss-pin...
I am using NRF52832 as Beacon, I want to classify the RSSI as High, Medium, Low, and Poor based on RSSI.
I am using SDK14.2.0 for Beacon and Gateway.
And using +4dBm Tx...
We are using Mesh SDK 3.2.0 and nRF52840 DK.
We wanted to use p_meta->p_core_metadata->params.scanner.adv_addr.addr as a unique identifier of the node hardware inside the...
After downloading and installing nrf mesh SDK as directed here https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-1-0/index . I'm not able to build any examples...
Hi, I am trying to use the RSSI viewer to scan RSSI values and verify the nearby beacons. But unfortunately RSSI viewer is NOT working and the following error message shown...
Hello.
I want to use the example of throughput with nRF52811.
I have changed it by looking at the nRF5 SDK Documentation, but it is not done.
(Software Development Kit...
I'm having issues building nRF5 SDK for Mesh v0.10.1-Alpha examples. On an Ubuntu 16.04 VM, I have installed the toolchain per the Debian/Ubuntu instructions and was able...
Hi,
I have two questions:
1) I am using ant bpwr tx example, SDK 15.2., Softdevice S212 v5.0.0, Segger embedded studio, nRF52832 DK and Garmin edge 520plus to display...
Hi there,
I have a custom built board with the nRF52840 and I'm trying to consistently transmit roughly 8 kilobytes per second or 64 kbits/s which seems way under the what...
Hello,
I'm working on a project that have with multirole to do, i have 3 device one act as master after a button is pressed, now i want to establish a connection between...
Hi,
I am having some issues with DFU and Keil.
I am loading Softdevice s140 v7.0.1 via nRF Connect and then programming a secure BLE bootloader using nrfjprog.
The bootloader...
Hi everybody,
I have a question about the number of data pakets which I can send with the BLE. Every data paket has a range of 20 Byte.
Now I want to send about 55 of...
